TMK063UJ060DP-F [TAIYO YUDEN]
Ceramic Capacitor, Multilayer, Ceramic, 25V, 8.33% +Tol, 8.33% -Tol, UJ, -750+/-120ppm/Cel TC, 0.000006uF, Surface Mount, 0201, CHIP, ROHS COMPLIANT;
| 型号： | TMK063UJ060DP-F |
| 厂家： | 
TAIYO YUDEN (U.S.A.), INC |
| 描述： | Ceramic Capacitor, Multilayer, Ceramic, 25V, 8.33% +Tol, 8.33% -Tol, UJ, -750+/-120ppm/Cel TC, 0.000006uF, Surface Mount, 0201, CHIP, ROHS COMPLIANT 电容器 |
| 文件： | 总17页 (文件大小：1002K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Notice for TAIYO YUDEN productsꢀ
Please read this notice before using the TAIYO YUDEN products.
1
REMINDERS
■Product information in this catalog is as of October 2008. All of the contents specified herein are
subject to change without notice due to technical improvements, etc. Therefore, please check for the
latest information carefully before practical application or usage of the Products.
Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment
incorporating such products, which are caused under the conditions other than those specified in this
catalog or individual specification.
■Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual
specification is available.
■Please conduct validation and verification of products in actual condition of mounting and operating
environment before commercial shipment of the equipment.
■All electronic components or functional modules listed in this catalog are developed, designed and
intended for use in general electronics equipment.(for AV, office automation, household, office supply,
information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the
components or devices into any equipment in the field such as transportation,( automotive control, train
control, ship control), transportation signal, disaster prevention, medical, public information network
(telephone exchange, base station) etc. which may have direct influence to harm or injure a human
body, please contact Taiyo Yuden Co., Ltd. for more detail in advance.
Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear
control, submarine system, military, etc. where higher safety and reliability are especially required.
In addition, even electronic components or functional modules that are used for the general electronic
equipment, if the equipment or the electric circuit require high safety or reliability function or
performances, a sufficient reliability evaluation check for safety shall be performed before commercial
shipment and moreover, due consideration to install a protective circuit is strongly recommended at
customer's design stage.
■The contents of this catalog are applicable to the products which are purchased from our sales offices
or distributors (so called“TAIYO YUDEN’s official sales channel”).
It is only applicable to the products purchased from any of TAIYO YUDEN’s official sales channel.
■Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that
may occur in connection with a third party's intellectual property rights and other related rights arising
from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights.
■Caution for export
Certain items in this catalog may require specific procedures for export according to“Foreign
Exchange and Foreign Trade Control Law”of Japan,“U.S. Export Administration Regulations”, and
other applicable regulations. Should you have any question or inquiry on this matter, please contact our
sales staff.
Should you have any question or inquiry on this matter, please contact our sales staff.
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
3
△
△
一般積層セラミックコンデンサ
（温度補償用・Class 1）
STANDARD MULTILAYER
CERAMIC CAPACITORS
(CLASS1 : TEMPERATURE COMPENSATING
DIELECTRIC TYPE)
OPERATING TEMP.
－55～＋125℃
特長ꢀFEATURES
・実装密度の向上が図れます
・Improve Higher Mounting Densities.
・Multilayer block structure provides higher reliability
・A wide range of capacitance values available in standard case sizes.
・モノリシックの構造のため、信
頼性が高い
・同
一形状、静電容量範囲が広い
用途ꢀAPPLICATIONS
・一般電子機器用
・General electronic equipment
・通信
機器用（携帯電話、PHS、コードレス電話 etc.）
・Communication equipment（cellular phone, PHS, other wireless applica-
tions, etc.）
形名表記法ꢀORDERING CODE
1
2
4
6
7
9
容量許容差
個別仕様
定格電圧〔VDC〕
形状寸法（EIA）L×W〔mm〕
042（01005）
063（0201）
105（0402）
公称静電容量〔pF〕
E
T
16
25
50
0.4×0.2
0.6×0.3
1.0×0.5
例
C
D
F
J
K
±
±
±
±
0.25 pF
0.5 pF
－
標準
0R5
010
100
0.5
1
10
U
1
5
pF
%
%
10
包装
±10ꢀ
※R＝小数点
5
シリーズ名
φ178mm テーピング
（2mmピッチ）
F
温度特性〔ppm/℃〕
C□ －150：CG、CH、CJ、CK
R□ －220：RH、
8
M
積層コンデンサ
製品
厚 み〔mm〕
C
P
V
0.2
0.3
0.5
3
S□ －330：SH、SJ、SK
T□ －470：TJ、TK
U□ －750：UJ、UK
G
H
J
±30
±60
±120
11
端子電極
当社管理記号
K
メッキ品
W
0.5
S L
＋350～－1000
K
±250
△
標準品
□＝許容差
△＝スペース
_
U M K 1 0 5 C H 1 0 1 J V
F △
6
9
1
2
3
7
8
10
11
4
5
1
4
6
7
9
Capacitance tolerance
ꢀ
Special code
Rated voltage〔VDC〕
Dimensions（case size（）EIA）L×W〔mm
〕
Nominal capacitance〔pF〕
E
T
16
25
50
042（01005）
063（0201）
105（0402）
0.4×0.2
0.6×0.3
1.0×0.5
example
C
D
F
J
K
±
±
±
±
0.25 pF
0.5 pF
－
Standard Products
0R5
010
100
0.5
1
10
U
1
5
pF
%
%
10
2
±10ꢀ
Packagingꢀ
*R=decimal point
5
φ178mm Taping
（2mm pitch）
Series name
F
8
Multilayer ceramic
capacitor
Temperature characteristics〔ppm/℃〕
C□ －150：CG、CH、CJ、CK
R□ －220：RH、
S□ －330：SH、SJ、SK
T□ －470：TJ、TK
U□ －750：UJ、UK
M
Thickness[mm]
C
P
V
0.2
3
G
H
J
±30
±60
±120
±250
0.3
0.5
0.5
11
End terminationꢀꢀ
K
Plated
Internal code
W
S L
＋350～－1000
K
△
Standard Products
□＝Tolerance
△＝Blank space
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
56
△
△
外形寸法ꢀEXTERNAL DIMENSIONS
Type（EIA）
□MK042
（01005）
□MK063
（0201）
□MK105
（0402）
L
W
T
e
0.4±0.02
0.2±0.02
0.2±0.02
0.1±0.03
C
P
（0.016±0.001）（0.008±0.001）（0.008±0.001）
（0.004±0.001）
0.15±0.05
0.6±0.03
（0.024±0.001）（0.012±0.001）（0.012±0.001）
1.0±0.05 0.5±0.05 0.5±0.05
（0.039±0.002）（0.020±0.002） （0.020±0.002）
0.3±0.03
0.3±0.03
（0.006±0.002）
0.25±0.10
W, V
（0.010±0.004）
Unit：mm（inch）
4
概略バリエーションꢀAVAILABLE CAPACITANCE RANGE
温度特性ꢀTemperature Characteristics
Type
042
063
105
温度特性
温度係数範囲
C□ C□
U□ C□ U□ SL R□ S□ T□
Temp.char.
VDC
使用温度範囲
※1
Temperature
〔ppm/℃〕
Cap
[ pF]
0.5
1
1.5
2
3
4
5
6
7
8
9
10
12
15
18
Operating Temp. range
16V
25V
50V
char.（EIA） Temperature coefficient range
［pF：3digits］
C K（C0K）
C J（C0J）
C H（C0H）
C G（C0G）
R H（R2H）
S K（S2K）
S J（S2J）
S H（S2H）
T K（T2K）
T J（T2J）
U K（U2K）
U J（U2J）
S L
0±250
0±120
0±60
0R5
010
1R5
020
030
040
050
060
070
080
090
100
120
150
180
220
270
330
390
470
560
680
820
101
121
151
181
221
271
331
391
471
561
681
821
102
W
0±30
P
－220±60
－330±250
－330±120
－330±60
－470±250
－470±120
－750±250
－750±120
－1000～＋350
W
W
W
－55～＋125℃
W
C
P
22
27
33
39
47
V
56
68
82
100
120
150
180
220
270
330
390
470
560
680
820
1000
V
※1：20℃における静電容量を基
ꢀꢀ Based on the capacitance at 20℃
準。
静電容量許容差ꢀCapacitance Tolerance Symbol
V
記号
Symbol
許容差
Tolerance
区分
Item
C
D
F
±0.25pF
±0.5 pF
±1pF
±5 %
±10 %
～5pF
～10pF
6～10 pF
11pF～
11pF～
注：グラフの記号は製品
の厚 み記号です。
Note: Letters in the table indicate thickness.
J
K
Q
※2
Q
区分
Item
Symbol
※1
≧400＋20・C
≧1000
～27pF
ꢀ30pF～
※1：C＝公称静電容量ꢀNominal capacitance〔pF〕
※2：測定周波数 Measurement Frequency= 1±0.1MHz（C≦1000pF）
1±0.1kHz（C＞1000pF）
Measurement voltage = 0.5～5Vrms（C≦1000pF）
1±0.2Vrms（C＞1000pF）
測定電圧
セレクションガイド
アイテム一覧
特性図
梱包
信
頼性
使用上の注意
Selection Guide
Part Numbers
Electrical Characteristics
Packaging
Reliability Data
Precautions
̶̶̶̶̶̶
P.12
P.58
P.98
P.102
P.108
etc
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
57
△
△
アイテム一覧ꢀPART NUMBERS
042TYPE
Class 1
定格電圧
温度特性
Temperature characteristics（EIA）
公称静電
容ꢀꢀ量
Capacitance
[pF]
EHS
静電容量
許 容 差
Capacitance
tolerance
厚
み
Rated
Voltage
（DC）
形ꢀ名
Ordering code
（Environmental
Hazardous
Thicknees
[mm]
（inch）
RK
CK CJ CHCG PK PJ PH (
RJ RH SK SJ SH TK TJ TH UK UJ
SL
)
(
)
(
)
(
) (
) (
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
Substances）
R2K
C0K C0J C0H C0G P2K P2J P2H
R2J R2H S2K S2J S2H T2K T2J T2H U2K U2J
EMK042 CK0R5□C
EMK042 CK010□C
EMK042 CK1R5□C
EMK042 CK020□C
EMK042 CJ030□C
EMK042 CH040□C
EMK042 CH050□C
EMK042 CH060□C
EMK042 CH070□C
EMK042 CH080□C
EMK042 CH090□C
EMK042 CH100□C
EMK042 CH120□C
EMK042 CH150□C
EMK042 CH180□C
EMK04 2 CH220□C
EMK04 2 CH270□C
EMK04 2 CH330□C
EMK04 2 CH390□C
EMK04 2 CH470□C
EMK04 2 CH560□C
EMK04 2 CH680□C
EMK04 2 CH820□C
EMK04 2 CH101□C
0.5
1
1.5
2
3
4
5
6
7
8
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
●
●
●
●
±0.25pF
±0.5pF
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
±0.5pF
±1pF
0.2±0.02
(0.008±0.001)
9
10
12
15
18
22
27
33
39
47
56
68
82
100
16V
±5%
±10%
注：形名の□には静電容量許容差記号が入ります。
□ Please specify the capacitance tolerance code.
063TYPE
Class 1
定格電圧
温度特性
Temperature characteristics（EIA）
公称静電
容ꢀꢀ量
Capacitance
[pF]
EHS
静電容量
許 容 差
厚
み
Rated
Voltage
（DC）
形ꢀ名
Ordering code
（Environmental
Hazardous
Capacitance Thicknees
[mm]
RK
CK CJ CHCG PK PJ PH (
RJ RH SK SJ SH TK TJ TH UK UJ
SL
tolerance
)
(
)
(
)
(
) (
) (
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
Substances）
R2K
C0K C0J C0H C0G P2K P2J P2H
R2J R2H S2K S2J S2H T2K T2J T2H U2K U2J
（inch）
TMK063
△
△
△
△
△
△
△
△
△
△
△
△
△
0R5□P
0.5
1
1.5
2
3
4
5
6
7
8
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
TMK063
TMK063
TMK063
TMK063
TMK063
TMK063
TMK063
TMK063
TMK063
TMK063
TMK063
TMK063
TMK063 △ 150□P
TMK063 CH180□P
TMK063 CH220□P
TMK063 CH270□P
TMK063 CH330□P
TMK063 CH390□P
TMK063 CH470□P
TMK063 CH560□P
TMK063 CH680□P
TMK063 CH820□P
TMK063 CH101□P
010□P
1R5□P
020□P
030□P
040□P
050□P
060□P
070□P
080□P
090□P
100□P
120□P
±0.25pF
±0.5pF
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
±0.5pF
±1pF
9
10
12
15
18
22
27
33
39
47
56
68
82
100
0.3±0.03
(0.012±0.001)
25V
±5%
±10%
注：形名の△には温度特性、□には静電容量許容差記号が入ります。
△ Please specify the temperature characteristics code and □ the capacitance tolerance code.
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
58
△
△
アイテム一覧ꢀPART NUMBERS
105TYPE
Class 1
定格電圧
温度特性
Temperature characteristics(EIA)
公称静電
容ꢀꢀ量
EHS
静電容量
許 容 差
厚
み
Rated
Voltage
(DC)
形ꢀ名
Ordering code
(Environmental
Hazardous
Thicknees
[mm]
(inch)
Capacitance Capacitance
RK
CK CJ CHCG PK PJ PH (
RJ RH SK SJ SH TK TJ TH UK UJ
SL
)
tolerance
(
)
(
)
(
) (
) (
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
Substances)
R2K
C0K C0J C0H C0G P2K P2J P2H
R2J R2H S2K S2J S2H T2K T2J T2H U2K U2J
[pF]
UMK105 △ 0R5□W
UMK105 △ 010□W
0.5
1
1.5
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
4
UMK105
△
1R5□W
±0.25pF
UMK105 △ 020□W
UMK105 △ 030□W
UMK105 △ 040□W
UMK105 △ 050□W
UMK105 △ 060□W
UMK105 △ 070□W
UMK105 △ 080□○
2
±0.5pF
3
4
5
6
7
8
9
10
12
15
18
22
27
33
39
47
56
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
±0.5pF
±1pF
UMK105
UMK105 △ 100□○
UMK105 120□○
△
090□○
△
UMK105 △ 150□○
UMK105 △ 180□○
UMK105 △ 220□ V
UMK105 △ 270□ V
UMK105 △ 330□ V
UMK105 △ 390□ V
UMK105 △ 470□ V
UMK105 △ 560□ V
UMK105 △ 680□ V
UMK105 △ 820□ V
0.5±0.05
(0.020±0.002)
50V
68
82
UMK105
△
101□ V
100 ±5%
±10%
UMK105 △ 121□ V
UMK105 △ 151□ V
UMK105 △ 181□ V
120
150
180
220
270
330
120
150
180
220
270
330
UMK105
△ 221□ V
UMK105 △ 271□ V
UMK105 △ 331□ V
UMK105 SL 121□ V
UMK105 SL 151□ V
UMK105 SL 181□ V
UMK105 SL 221□ V
UMK105 SL 271□ V
UMK105 SL 331□ V
●
●
●
●
●
●
注：形名の△には温度特性、□には静電容量許容差記号、○にはCHの時には「V」、UJの時は「W」が入ります。
△ Please specify the temperature characteristics code. □ Please specify the capacitance tolerance code.
○ comes to“V”when △ is“CH”and“W”when △ is“UJ”.
105TYPE
Class 1
定格電圧
Rated
Voltage
(DC)
温度特性
Temperature characteristics(EIA)
公称静電
容ꢀꢀ量
Capacitance
[pF]
EHS
静電容量
許 容 差
Capacitance
tolerance
厚
み
形ꢀ名
Ordering code
(Environmental
Hazardous
Thicknees
[mm]
(inch)
RK
CK CJ CHCG PK PJ PH (
RJ RH SK SJ SH TK TJ TH UK UJ
SL
)
(
)
(
)
(
) (
) (
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
(
)
Substances)
R2K
C0K C0J C0H C0G P2K P2J P2H
R2J R2H S2K S2J S2H T2K T2J T2H U2K U2J
UMK105 △ 0R5BW
UMK105 △ 010BW
UMK105 △ 1R2BW
UMK105 △ 1R5BW
UMK105 △ 1R8BW
UMK105 △ 2R2 JW
UMK105 △ 2R7 JW
UMK105 △ 3R3 JW
UMK105 △ 3R9 JW
UMK105 △ 4R7 JW
UMK105 △ 5R6 JW
UMK105 △ 6R8 JW
UMK105 △ 8R2 JW
UMK105 △ 100 JW
UMK105 △ 120 JW
UMK105 △ 150 JW
UMK105 △ 180 JW
UMK105 △ 200 JW
0.5
1
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
RoHS
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
±0.1pF
1.2
1.5
1.8
2.2
2.7
3.3
3.9
4.7
5.6
6.8
8.2
10
●
●
0.5±0.05
(0.020±0.002)
50V
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
±5%
12
15
18
20
注：形名の△には温度特性が入ります。
△ Please specify the temperature characteristics code.
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
59
△
△
梱包ꢀPACKAGING
①最小受注単位数 Minimum Quantity
■テーピング梱包ꢀ Taped packagingꢀ
標準数量
製品
厚 み
Standard quantity
[ pcs ]
形式（EIA）
Thickness
Type
紙テープ エンボステープ
code
mm（inch）
paper
Embossed tape
□MK04（2 01005
）
0.2（0.008）
0.3（0.012）
0.3（0.012）
0.45（0.018）
0.3（0.012）
C
P
15000
̶
□MK063（0201）
15000
10000
10000
10000
̶
̶
̶
̶
P
□2K09（6 0302）
K
□WK105（0204）
□MK105（0402）
□VK105（0402）
P
V, W
W
K
0.5（0.020）
0.45（0.018）
0.5（0.020）
0.8（0.031）
0.5（0.020）
0.8（0.031）
0.6（0.024）
0.45（0.018）
0.85（0.033）
1.25（0.049）
0.85（0.033）
0.85（0.033）
0.85（0.033）
1.15（0.045）
1.25（0.049）
1.6（0.063）
0.85（0.033）
1.15（0.045）
1.5（0.059）
1.9（0.075）
2.0ma（x 0.079）
4000
̶
̶
4000
̶
□MK107（0603）
□WK10（7 0306）
V
A
4000
4000
4000
4000
4000
4000
̶
̶
V
A
B
K
D
G
D
D
D
F
̶
̶
̶
̶
3000
̶
̶
□2K11（0 0504）
□MK212（0805）
□WK21（2 0508）
□4K21（2 0805）
□2K21（2 0805）
4000
4000
4000
̶
̶
̶
3000
2000
□MK316（1206）
G
L
※□WK
D
F
③バルクカセットꢀBulk Cassette
̶
2000
H
N
Y
□MK325（1210）
□MK432（1812）
̶
̶
̶
2000
500（Ｔ）,
1000（Ｐ）
2.5（0.098）
2.5（0.098）
M
M
500
※プレスポケットタイプは、
ꢀボトムテープ無し。
②テーピング材質ꢀTaping material
Unit：mm（inch）
105, 107, 212形状で個
別対応致しますのでお問い合せ下さい。
Please contact any of our offices for accepting your requirement accord-
ing to dimensions 0402, 0603, 0805.(inch)
※□WK
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
98
△
△
梱包ꢀPACKAGING
③テーピング寸法ꢀTaping dimensionsꢀ
ꢀ紙テープꢀPaper Tape（8mm幅（）0.315inches wide）
エンボステープꢀEmbossed tape（8mm幅（）0.315inches wide）
部品
挿入角穴
4
T1
2.0±0.05 2.0±0.05
チップ挿入部
挿入ピッチ
テープ厚 み
Type
Chip Cavity
Insertion Pitch Tape Thickness
（ＥＩＡ）
Ａ
Ｂ
Ｆ
Ｔ
T1
チップ挿入部
Chip cavity
挿入ピッチ テープ厚 み
0.25
（0.010）
0.45
2.0±0.05
0.36max.
0.27max.
Type
□MK042（01005）
□MK063（0201）
□WK105（0204）
Insertion Pitch Tape Thickness
（0.018） （0.079±0.002） （0.014） （0.011）
（EIA）
A
B
F
K
T
0.37
（0.016）
0.67
2.0±0.05
0.45max.
0.42max.
1.0
1.8
1.3max. 0.25±0.1
（0.027） （0.079±0.002） （0.018） （0.017）
□WK107（0306）
□MK212（0805）
□MK316（1206）
（0.039） （0.071）
1.655 2.4
（0.065） （0.094）
2.0 3.6
（0.079） （0.142）
（0.051max.）（0.01±0.004）
0.65
（0.026）
1.15
2.0±0.05
0.45max 0.42max
（0.045） （0.079±0.002）（0.018max）（0.017max）
4.0±0.1
Unit：mm（inch）
（0.157±0.004）3.4max. 0.6max.
（0.134max.）（0.024max.）
部品
挿入角穴
2.8
3.6
□MK325（1210）
（0.110） （0.142）
Unit：mm（inch）
エンボステープꢀEmbossed tape（12mm幅（）0.472inches wide）
2.0±0.05 2.0±0.05
チップ挿入部
Chip Cavity
挿入ピッチ テープ厚 み
Type
Insertion Pitch Tape Thickness
（EIA）
A
B
F
T
0.72
（0.028）
0.655
1.02
52.0±0.05 0.45max.(0.018max)
□2K096（0302）
□MK105（0402）
（0.040） （0.079±0.002）0.6max.(0.024max)
1.155
52.0±0.05
0.8max.
□VK105（0402） （0.026）
（0.045） （0.079±0.002）（0.031max.）
Unit：mm（inch）
チップ挿入部
Chip cavity
挿入ピッチ テープ厚 み
Type
Insertion Pitch Tape Thickness
（EIA）
A
B
F
K
T
3.7
4.9
8.0±0.1
4.0max. 0.6max.
□MK432（1812）
（0.146）
（0.193） （0.315±0.004） （0.157max.）（0.024max.）
Unit：mm（inch）
チップ挿入部
Chip Cavity
挿入ピッチ テープ厚 み
Type
Insertion Pitch Tape Thickness
（EIA）
A
B
F
T
□MK10（7 0603）
□WK10（7 0306）
1.0
1.8
4.0±0.1
1.1max.
（0.039）
1.15
（0.071） （0.157±0.004） （0.043max.）
1.55
4.0±0.1
1.0max.
□2K110（0504）
（0.045）
（0.061） （0.157±0.004） （0.039max.）
□MK212（0805）
□WK212（0508）
1.655
2.4
□4K212（0805） （0.065）
□2K212（0805）
（0.094）
4.0±0.1
1.1max.
（0.157±0.004） （0.043max.）
2.0
□MK316（1206）
（0.079）
3.6
（0.142）
Unit：mm（inch）
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
99
△
△
梱包ꢀPACKAGING
④リーダー部／空部ꢀLeader and Blank portionꢀ
160mm以上
（6.3inches or more
100mm以上
）
（3.94inches or more）
引き出し方向
Direction of tape feed
400mm以上
（15.7inches or more）
⑤リール寸法ꢀReel sizeꢀ
⑥トップテープ強度ꢀTop Tape Strengthꢀ
トップテープのはがし力は下図矢印方向にて0.1～0.7Nとなります。
The top tape requires a peel-off force of 0.1～0.7N in the direction of the
arrow as illustrated below.
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
100
△
△
RELIABILITY DATA
1/3
Multilayer Ceramic Capacitor Chips
Specified Value
Temperature Compensating（Class 1）
Item
High Permitivity（Class 2）
Test Methods and Remarks
Standard
High Frequency Type
Standard Note1
BJ：－55 to ＋125℃
High Value
1.Operating Temperature
Range
－25 to ＋85℃
－55 to ＋125℃
High Capacitance Type
High Capacitance Type
BJ（X7R）：－55～＋125℃, BJ（X5R）：－55～＋85℃
E（Y5U）：－30～＋85℃, F（Y5V）：－30～＋85℃
BJ（X7R）：－55～＋125℃, BJ（X5R）：－55～＋85℃
E（Y5U）：－30～＋85℃, F（Y5V）：－30～＋85℃
F：－25 to ＋85℃
BJ：－55 to ＋125℃
F：－25 to ＋85℃
50VDC,25VDC
2.Storage Temperature
Range
－25 to ＋85℃
－55 to ＋125℃
4
3.Rated Voltage
16VDC
50VDC
50VDC,35VDC,25VDC
16VDC,10VDC,6.3VDC
4DVC, 2.5VDC
50VDC,25VDC,
16VDC
4.Withstanding Voltage
No abnormality
No breakdown or damage
Applied voltage: Rated voltage×3 （Class 1）
Rated voltage×2.5（Class 2）
N o b re a k d o w n o r
damage
Between terminals
Duration: 1 to 5 sec.
Charge/discharge current: 50mA max.（Class 1,2）
5.Insulation Resistance
500 MΩμF. or 10000 MΩ., whichever is the Applied voltage: Rated voltage
10000 MΩ min.
smaller.
Duration: 60±5 sec.
Note 5
Charge/discharge current: 50mA max.
6.Capacitance（Tolerance）
0.5 to 2 pF : ±0.1 pF
2.2 to 5.1 pF : ±5%
BJ: ±10%, ±20%
＋80
BJ：±10％、±20％
F：－20％／＋80％
0.5 to 5 pF: ±0.25 pF
1 to 10pF: ±0.5 pF
5 to 10 pF: ±1 pF
11 pF or over: ± 5%
±10%
Measuring frequency：
Class1： 1ＭHz±10%（C≦1000pF）
F：
%
－20
1ｋHz±10%（C＞1000pF）
Class2： 1ｋHz±10%（C≦10μF）
120Hz±10Hz（C＞10μF）
Measuring voltage：
Note 4
Class1：0.5～5Vrms（C≦1000pF）
1±0.2Vrms（C＞1000pF）
105TYPER△, S△, T△, U△ only
0.5～2pF: ±0.1pF
Class2： 1±0.2Vrms（C≦10μF）
0.5±0.1Vrms（C＞10μF）
2.2～20pF: ±
5%
Bias application: None
7.Q or Tangent of Loss Angle
（tan δ）
R e f e r t o d e t a i l e d BJ: 2.5% max（. 50V, 25V）
Under 30 pF
BJ：2.5％ max.
F：7％ max.
Note 4
Multilayer:
Measuring frequency：
specification
F: 5.0% max.（50V, 25V）
Note 4
: Q≧400 ＋ 20C
Class1： 1ＭHz±10%（C≦1000pF）
30 pF or over : Q≧1000
C= Nominal capacitance
1ｋHz±10%（C＞1000pF）
Class2： 1ｋHz±10%（C≦10μF）
120Hz±10Hz（C＞10μF）
Measuring voltage：
Note 4ꢀꢀꢀꢀ Class1：0.5～5Vrms（C≦1000pF）
1±0.2Vrms（C＞1000pF）
Class2： 1±0.2Vrms（C≦10μF）
0.5±0.1Vrms（C＞10μF）
Bias application: None
HighーFrequencyーMultilayer:
Measuring frequency: 1GHz
Measuring equipment: HP4291A
Measuring jig: HP16192A
8.Temperature
（Without
CH：0±60
BJ：±10％（－25～85℃）
＋30
CK：0±250
According to JIS C 5102 clause 7.12.
Temperature compensating:
BJ：±10％
Characteristic
voltage ap-
RH：－220±60
（ppm/℃）
F：
％（－25～85℃）
－80
CJ：0±120
ꢀ（－25～＋85℃）
F：＋30％／－80％
ꢀ（－25～＋85℃）
BJ（X7R、X5R）：
ꢀꢀ±15％
of Capacitance
BJ（X7R）：±15％
CH：0±60
Measurement of capacitance at 20℃ and 85℃ shall be
made to calculate temperature characteristic by the fol-
lowing equation.
plication）
＋22
F（Y5V）：ꢀꢀ％
CG：0±30
－82
RH：－220±60
SK：－330±250
SJ：－330±120
SH：－330±60
TK：－470±250
TJ：－470±120
UK：－750±250
UJ：－750±120
SL ： ＋ 350 to ー 1000
（ppm/℃）
（C85ー C20
C20×△T
）
× 106ꢀ（ppm/℃）
F（Y5V）：
High permitivity:
ꢀꢀ＋22％／－82％
Change of maximum capacitance deviation in step 1 to 5
Temperature at step 1: ＋20℃
Temperature at step 2: minimum operating temperature
Temperature at step 3: ＋20℃（Reference temperature）
Temperature at step 4: maximum operating temperature
Temperature at step 5: ＋20℃
Reference temperature for X7R, X5R, Y5U and Y5V shall be ＋25℃
9.Resistance to Flexure of
Appearance:
Appearance:
Appearance:
Warp: 1mm
Testing board: glass epoxyーresin substrate
Thickness: 1.6mm（063 TYPE : 0.8mm）
The measurement shall be made with board in the bent position.
Substrate
No abnormality
No abnormality
No abnormality
Capacitance change: Capacitance change:
Capacitance change:
Within ±5% or ±0.5 pF,
whichever is larger.
Within±0.5 pF
BJ：Within ±12.5%
F：Within ±30%
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
103
△
△
RELIABILITY DATA
2/3
Multilayer Ceramic Capacitor Chips
Specified Value
Temperature Compensating（Class 1）
Standard High Frequency Type
Item
High Permittivity（Class 2）
Standard Note1 High Value
Test Methods and Remarks
10.Body Strength
No mechanical dam-
age.
High Frequency Multilayer:
Applied force: 5N
Duration: 10 sec.
4
A
A
A
（LW Reverse）
11.Adhesion of Electrode
No separation or indication of separation of electrode.
Applied force: 5N
（01005, 0201, 0302 TYPE 2N）
Duration: 30±5 sec.
12.Solderability
At least 95% of terminal electrode is covered by new solder.
Solder temperature: 230±5℃
Duration: 4±1 sec.
13.Resistance to soldering
Appearance: No ab- Appearance: No ab- Appearance: No abnormality
Preconditioning: Thermal treatment（at 150℃ for 1 hr）
（Applicable to Class 2.）
normality
normality
Capacitance change: Within ±7.5%（BJ）
Within ±20%（F）
Capacitance change: Capacitance change:
W i t h i n ± 2.5% o r Within ±2.5%
±0.25pF, whichever is Q: Initial value
Solder temperature: 270±5℃
tan δ: Initial value
Note 4 Duration: 3±0.5 sec.
Insulation resistance: Initial value
Preheating conditions: 80 to 100℃, 2 to 5 min. or 5 to 10 min.
150 to 200℃, 2 to 5 min. or 5 to 10 min.
Recovery: Recovery for the following period under the
standard condition after the test.
larger.
Insulation resistance: Withstanding voltage（between terminals）: No
Initial value abnormality
Q: Initial value
Insulation resistance: Withstanding voltage
Initial value （between terminals）:
6～24 hrs（Class 1）
Withstanding voltage No abnormality
（between terminals）:
24±2 hrs（Class 2）
No abnormality
14.Thermal shock
Appearance: No ab- Appearance: No ab- Appearance: No abnormality
Preconditioning: Thermal treatment（at 150℃ for 1 hr）
（Applicable to Class 2.）
normality
normality
Capacitance change: Within ±7.5%（BJ）
Within ±20%（F）
Capacitance change: Capacitance change:
W i t h i n ± 2.5% o r Within ±0.25pF
±0.25pF, whichever is Q: Initial value
Conditions for 1 cycle:
Note 4 Step 1: Minimum operating temperature ＋－
℃
30±3 min.
2 to 3 min.
30±3 min.
2 to 3 min.
0
tan δ: Initial value
3
Insulation resistance: Initial value
Step 2: Room temperature
Insulation resistance: Withstanding voltage（between terminals）: No Step 3: Maximum operating temperature －＋
℃
0
3
larger.
Q: Initial value
Initial value
abnormality
Step 4: Room temperature
Number of cycles: 5 times
Insulation resistance: Withstanding voltage
Initial value （between terminals）:
Recovery after the test: 6～24 hrs（Class 1）
24±2 hrs（Class 2）
Withstanding voltage No abnormality
（between terminals）:
No abnormality
15.Damp Heat（steady state） Appearance: No ab- Appearance: No ab- Appearance: No ab- Appearance: No ab- Multilayer：
normality
normality
normality
normality
Preconditioning: Thermal treatment（at 150℃ for 1 hr）
（Applicable to Class 2.）
Capacitance change: Capacitance change: Capacitance change:
Capacitance change:
BJ:Within ±12.5%
Note 4
BJ: Within ±12.5%
F: Within ±30%
Within ±5% or ±0.5pF, Within ±0.5pF,
Temperature: 40±2℃
whichever is larger.
Q:
Insulation resistance:
1000 MΩ min.
Humidity: 90 to 95% RH
＋24
tan δ: BJ: 5.0% max.
tan δ:
Duration: 500 － hrs
0
F: 7.5% max. BJ: 5.0% max. Note 4.
F: 11.0% max.
C≧30 pF : Q≧350
10 ≦ C＜ 30 pF: Q≧
275 ＋ 2.5C
Recovery: Recovery for the following period under the
standard condition after the removal from test chamber.
6～24 hrs（Class 1）
Note 4
Insulation resistance:
50 MΩμF or 1000 MΩ
whichever is smaller.
Note 5
Insulation resistance:
50 MΩμF or 1000 MΩ
whichever is smaller.
Note 5
C＜10 pF
＋ 10C
: Q≧200
24±2 hrs（Class 2）
HighーFrequency Multilayer:
C: Nominal capacitance
Insulation resistance:
1000 MΩ min.
Temperature: 60±2℃
Humidity: 90 to 95% RH
＋24
Duration: 500 － hrs
0
Recovery: Recovery for the following period under the
standard condition after the removal from test chamber.
6～24 hrs（Class 1）
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
105
△
△
RELIABILITY DATA
3/3
Multilayer Ceramic Capacitor Chips
Specified Value
Temperature Compensating（Class 1）
Standard High Frequency Type
Item
High Permittivity（Class 2）
Test Methods and Remarks
Standard Note1
High Value
16.Loading under Damp Heat Appearance: No ab- Appearance: No ab-
normality normality
According to JIS C 5102 Clause 9. 9.
Multilayer:
Appearance: No ab-
normality
Appearance: No ab-
normality
Capacitance change: Capacitance change:
Within ±7.5% or ± C≦2 pF:Within ±0.4 pF
0.75pF, whichever is C＞2 pF: Within ±0.75
Preconditioning: Voltage treatment（Class 2）
Temperature: 40±2℃
Capacitance change:
BJ: Within ±12.5%
F: Within ±30%
Note 4
Capacitance change:
BJ：Within±12.5％
F：Within±30％
Note 4
4
Humidity: 90 to 95% RH
＋24
larger.
pF
Duration: 500 － hrs
0
Q: C≧30 pF: Q≧200
C＜30 pF: Q≧100 ＋ tance
10C/3
C ： Nominal capaci-
Applied voltage: Rated voltage
tan δ: BJ: 5.0% max.
F: 7.5% max.
tanδ：
BJ：5.0％max.
F：11％max.
Charge and discharge current: 50mA max.（Class 1,2）
Recovery: Recovery for the following period under the standard
condition after the removal from test chamber.
6～24 hrs（Class 1）
24±2 hrs（Class 2）
HighーFrequency Multilayer:
Insulation resistance:
Note 4
C ： Nominal capaci- 500 MΩ min.
tance
Insulation resistance:
25 MΩμF or 500 MΩ,
whichever is the smaller.
Note 5
Note 4
Insulation resistance:
25 MΩμF or 500 MΩ,
whichever is the smaller.
Note 5
Insulation resistance:
500 MΩ min.
Temperature: 60±2℃
Humidity: 90 to 95% RH
＋24
Duration: 500
hrs
－
0
Applied voltage: Rated voltage
Charge and discharge current: 50mA max.
Recovery: 6～24 hrs of recovery under the standard
condition after the removal from test chamber.
17.Loading at High Tempera-
Appearance: No ab- Appearance: No ab-
According to JIS C 5102 clause 9.10.
Multilayer:
Appearance: No abnormality
Capacitance change:
BJ：Within±12.5％
Within±20％※※
Within±25％※※
F：Within±30％
Note 4
ture
normality
normality
Appearance: No ab-
normality
Capacitance change:
Within ±3% or
±0.3pF, whichever is
larger.
Capacitance change:
Within ±3% or ±
0.3pF, whichever is
larger.
Preconditioning: Voltage treatment（Class 2）
Temperature:125±3℃（Class 1, Class 2: B, BJ（X7R）
）
Capacitance change:
BJ: Within ±12.5%
F: Within ±30%
Note 4
85±2℃（Class 2: BJ,F）
＋48
Duration: 1000－ hrs
0
Q: C≧30 pF : Q≧350 Insulation resistance:
Applied voltage: Rated voltage×2 Note 6
10≦C＜30 pF: Q≧275
＋ 2.5C
C＜10 pF: Q≧200 ＋
10C
1000 MΩ min.
Recovery: Recovery for the following period under the
standard condition after the removal from test chamber.
ꢀꢀꢀ6～24 hrs（Class 1）
tan δ:
BJ: 4.0% max.
tanδ：
BJ：5.0％max.
F：11％max.ꢀ
Note 4
F: 7.5% max.
ꢀꢀꢀ 24±2 hrs（Class 2）
Note 4
C：Nominal
capacitance
HighーFrequency Multilayer:
Insulation resistance:
50 MΩμF or 1000 MΩ,
whichever is smaller.
Note 5
Insulation resistance:
50 MΩμF or 1000 MΩ,
whichever is smaller.
Note 5
Temperature: 125±3℃（Class 1）
＋48
Insulation resistance:
1000 MΩ min.
Duration: 1000－ hrs
0
Applied voltage: Rated voltage×2
Recovery: 6～24 hrs of recovery under the standard
condition after the removal from test chamber.
Note 1
Note 2
Note 3
:For 105 type, specified in "High value".
:Thermal treatment（Multilayer）: 1 hr of thermal treatment at 150 ＋0 /－10 ℃ followed by 24±2 hrs of recovery under the standard condition shall be performed before the measurement.
Voltage treatment（Multilayer）: 1 hr of voltage treatment under the specified temperature and voltage for testing followed by 24±2 hrs of recovery under the standard condition shall be performed before the measurement.
:
Note 4, 5 :The figure indicates typical inspection. Please refer to individual specifications.
Note 6 :Some of the parts are applicable in rated voltage×1.5. Please refer to individual specifications.
Note on standard condition: "standard condition" referred to herein is defined as follows: 5 to 35℃ of temperature, 45 to 85% relative humidity, and 86 to 106kPa of air pressure.
When there are questions concerning measurement results: In order to provide correlation data, the test shall be conducted under condition of 20±2℃ of temperature, 60 to 70% relative
humidity, and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition."
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
107
△
△
PRECAUTIONS
1/6
Precautions on the use of Multilayer Ceramic Capacitors
Stages
Precautions
Technical considerations
1.Circuit Design
Verification of operating environment, electrical rating and per-
formance
1. A malfunction in medical equipment, spacecraft, nuclear
reactors, etc. may cause serious harm to human life or have
severe social ramifications. As such, any capacitors to be
used in such equipment may require higher safety and/or
reliability considerations and should be clearly differentiated
from components used in general purpose applications.
4
Operating Voltage（Verification of Rated voltage）
1. The operating voltage for capacitors must always be lower
than their rated values.
If an AC voltage is loaded on a DC voltage, the sum of the
two peak voltages should be lower than the rated value of
the capacitor chosen. For a circuit where both an AC and a
pulse voltage may be present, the sum of their peak voltages
should also be lower than the capacitor's rated voltage.
2. Even if the applied voltage is lower than the rated value, the
reliability of capacitors might be reduced if either a high fre-
quency AC voltage or a pulse voltage having rapid rise time
is present in the circuit.
1.The following diagrams and tables show some examples of recommended patterns to
prevent excessive solder amourts.（larger fillets which extend above the component
end terminations）
2.PCB Design
Pattern configurations
（Design of Land-patterns）
1. When capacitors are mounted on a PCB, the amount of
solder used（size of fillet）can directly affect capacitor per-
formance. Therefore, the following items must be carefully
considered in the design of solder land patterns:
（1）The amount of solder applied can affect the ability of
chips to withstand mechanical stresses which may lead
to breaking or cracking. Therefore, when designing
land-patterns it is necessary to consider the appropri-
ate size and configuration of the solder pads which in
turn determines the amount of solder necessary to form
the fillets.
Examples of improper pattern designs are also shown.
（1）Recommended land dimensions for a typical chip capacitor land patterns for PCBs
Recommended land dimensions for wave-soldering（unit: mm）
（2）When more than one part is jointly soldered onto the
same land or pad, the pad must be designed so that each
component's soldering point is separated by solder-resist.
Type
107
1.6
0.8
212
2.0
316
3.2
1.6
325
3.2
2.5
L
Size
W
51.25
A
0.8～1.0 1.0～1.4 1.8～2.5 1.8～2.5
0.5～0.8 0.8～1.5 0.8～1.7 0.8～1.7
0.6～0.8 0.9～1.2 1.2～1.6 1.8～2.5
B
C
Recommended land dimensions for reflow-soldering（unit: mm）
Type
042
0.4
0.2
063
0.6
0.3
105
1.0
0.5
107
1.6
0.8
212
2.0
316
3.2
1.6
325
3.2
2.5
432
4.5
3.2
L
Size
W
51.25
A
0.15～0.25 0.20～0.30 0.45～0.55 0.8～1.0 0.8～1.2 1.8～2.5 1.8～2.5 2.5～3.5
0.10～0.20 0.20～0.30 0.40～0.50 0.6～0.8 0.8～1.2 1.0～1.5 1.0～1.5 1.5～1.8
0.15～0.30 0.25～0.40 0.45～0.55 0.6～0.8 0.9～1.6 1.2～2.0 1.8～3.2 2.3～3.5
B
C
Excess solder can affect the ability of chips to withstand mechanical stresses. There-
fore, please take proper precautions when designing land-patterns.
Type 212（4 circuits）
2.0
L
1.25
W
a
b
c
d
0.5～0.6
0.5～0.6
0.2～0.3
0.5
Type 212（2 circuits） 110（2 circuits）096（2 circuits）
L
2.0
1.37
1.0
0.9
0.6
1.25
W
a
b
c
d
0.5～0.6
0.5～0.6
0.5～0.6
1.0
0.35～0.45 0.25～0.35
0.55～0.65 0.15～0.25
0.3～0.4
0.64
0.15～0.25
0.45
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
109
△
△
PRECAUTIONS
2/6
Precautions on the use of Multilayer Ceramic Capacitors
Stages
Precautions
Technical considerations
LWDC Recommended land dimensions for reflow-soldering
4
105
0.52
1.0
107
50.8
1.6
212
1.25
2.0
Type
L
W
A
B
C
0.18～0.22 0.25～0.3 0.5～0.7
0.2～0.25 0.3～0.4 0.4～0.5
0.9～1.1 1.5～1.7 1.9～2.1
（unit: mm）
2.PCB Design
（2）Examples of good and bad solder application
Not recommended
Recommended
Items
Mixed mounting
of SMD and
leaded compo-
nents
Component
placement close
to the chassis
Hand-soldering
of leaded
components
near mounted
components
Horizontal
component
placement
Pattern configurations
1-1. The following are examples of good and bad capacitor layout; SMD capacitors should
（Capacitor layout on panelized [breakaway] PC boards）
1. After capacitors have been mounted on the boards, chips
can be subjected to mechanical stresses in subsequent
manufacturing processes（PCB cutting, board inspection,
mounting of additional parts, assembly into the chassis, wave
soldering the reflow soldered boards etc.） For this reason,
planning pattern configurations and the position of SMD ca-
pacitors should be carefully performed to minimize stress.
be located to minimize any possible mechanical stresses from board warp or deflection.
Not recommended
Recommended
Deflection of
the board
1-2. To layout the capacitors for the breakaway PC board, it should be noted that the
amount of mechanical stresses given will vary depending on capacitor layout. The
example below shows recommendations for better design.
1-3. When breaking PC boards along their perforations, the amount of mechanical stress
on the capacitors can vary according to the method used. The following methods
are listed in order from least stressful to most stressful: push-back, slit, V-grooving,
and perforation. Thus, any ideal SMD capacitor layout must also consider the PCB
splitting procedure.
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
111
△
△
PRECAUTIONS
3/6
Precautions on the use of Multilayer Ceramic Capacitors
Stages
Precautions
Technical considerations
3.Considerations for auto-
Adjustment of mounting machine
1. If the lower limit of the pick-up nozzle is low, too much force may be imposed on the
capacitors, causing damage. To avoid this, the following points should be considered
before lowering the pick-up nozzle:
matic placement
1. Excessive impact load should not be imposed on the ca-
pacitors when mounting onto the PC boards.
2. The maintenance and inspection of the mounters should be
conducted periodically.
（1）The lower limit of the pick-up nozzle should be adjusted to the surface level of the
PC board after correcting for deflection of the board.
4
（2）The pick-up pressure should be adjusted between 1 and 3 N static loads.
（3）To reduce the amount of deflection of the board caused by impact of the pick-up
nozzle, supporting pins or back-up pins should be used under the PC board. The fol-
lowing diagrams show some typical examples of good pick-up nozzle placement:
Not recommended
Recommended
Single-sided
mounting
Double-sided
mounting
2. As the alignment pin wears out, adjustment of the nozzle height can cause chipping or
cracking of the capacitors because of mechanical impact on the capacitors. To avoid
this, the monitoring of the width between the alignment pin in the stopped position, and
maintenance, inspection and replacement of the pin should be conducted periodically.
Selection of Adhesives
1. Some adhesives may cause reduced insulation resistance. The difference between
the shrinkage percentage of the adhesive and that of the capacitors may result in
stresses on the capacitors and lead to cracking. Moreover, too little or too much
adhesive applied to the board may adversely affect component placement, so the fol-
lowing precautions should be noted in the application of adhesives.
1. Mounting capacitors with adhesives in preliminary assembly,
before the soldering stage, may lead to degraded capacitor
characteristics unless the following factors are appropriately
checked; the size of land patterns, type of adhesive, amount
applied, hardening temperature and hardening period.
Therefore, it is imperative to consult the manufacturer of the
adhesives on proper usage and amounts of adhesive to use.
（1）Required adhesive characteristics
a. The adhesive should be strong enough to hold parts on the board during the mount-
ing & solder process.
b. The adhesive should have sufficient strength at high temperatures.
c. The adhesive should have good coating and thickness consistency.
d. The adhesive should be used during its prescribed shelf life.
e. The adhesive should harden rapidly
f. The adhesive must not be contaminated.
g. The adhesive should have excellent insulation characteristics.
h. The adhesive should not be toxic and have no emission of toxic gasses.
（2）The recommended amount of adhesives is as follows;
Figure
212/316 case sizes as examples
0.3mm min
a
b
c
100 ～120 μm
Adhesives should not contact the pad
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
113
△
△
PRECAUTIONS
4/6
Precautions on the use of Multilayer Ceramic Capacitors
Stages
4. Soldering
Precautions
Technical considerations
Selection of Flux
1-1. When too much halogenated substance（Chlorine, etc.）content is used to activate
the flux, or highly acidic flux is used, an excessive amount of residue after soldering
may lead to corrosion of the terminal electrodes or degradation of insulation resis-
tance on the surface of the capacitors.
1. Since flux may have a significant effect on the performance
of capacitors, it is necessary to verify the following condi-
tions prior to use;
（1）Flux used should be with less than or equal to 0.1 wt%
（equivelent to chroline）of halogenated content. Flux
having a strong acidity content should not be applied.
（2）When soldering capacitors on the board, the amount of
flux applied should be controlled at the optimum level.
（3）When using water-soluble flux, special care should be
taken to properly clean the boards.
1-2. Flux is used to increase solderability in flow soldering, but if too much is applied, a
large amount of flux gas may be emitted and may detrimentally affect solderability. To
minimize the amount of flux applied, it is recommended to use a flux-bubbling system.
1-3. Since the residue of water-soluble flux is easily dissolved by water content in the
air, the residue on the surface of capacitors in high humidity conditions may cause a
degradation of insulation resistance and therefore affect the reliability of the compo-
nents. The cleaning methods and the capability of the machines used should also be
considered carefully when selecting water-soluble flux.
4
Soldering
1-1. Preheating when soldering
Temperature, time, amount of solder, etc. are specified in ac-
cordance with the following recommended conditions.
Heating: Ceramic chip components should be preheated to within 100 to 130℃ of the
soldering.
Cooling: The temperature difference between the components and cleaning process
should not be greater than 100℃.
Ceramic chip capacitors are susceptible to thermal shock when exposed to rapid or concen-
trated heating or rapid cooling. Therefore, the soldering process must be conducted with
great care so as to prevent malfunction of the components due to excessive thermal shock.
Recommended conditions for soldering
[Reflow soldering]
Sn-Zn solder paste can affect MLCC reliability performance.
Please contact us prior to usage.
Temperature profile
Temperature（℃）
（Pb free soldering）
300
Peak 260℃ max
10 sec max
200
100
0
Gradually
cooling
Preheating
150℃
60 sec min
Heating above 230℃
40 sec max
※Ceramic chip components should be preheated to
within 100 to 130℃ of the soldering.
※Assured to be reflow soldering for 2 times.
Caution
1. The ideal condition is to have solder mass （fillet）controlled to 1/2 to 1/3 of the
thickness of the capacitor, as shown below:
Capacitor
Solder
PC board
2. Because excessive dwell times can detrimentally affect solderability, soldering du-
ration should be kept as close to recommended times as possible.
[Wave soldering]
Temperature profile
Temperature（℃）
（Pb free soldering）
300
Peak 260℃ max
10 sec max
200
100
0
Gradually
cooling
Preheating
150℃
120 sec min
※Ceramic chip components should be preheated to
within 100 to 130℃ of the soldering.
※Assured to be wave soldering for 1 time.
※Except for reflow soldering type.
Caution
1. Make sure the capacitors are preheated sufficiently.
2. The temperature difference between the capacitor and melted solder should not be
greater than 100 to 130℃
3. Cooling after soldering should be as gradual as possible.
4. Wave soldering must not be applied to the capacitors designated as for reflow sol-
dering only.
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
115
△
△
PRECAUTIONS
5/6
Precautions on the use of Multilayer Ceramic Capacitors
Stages
Precautions
Technical considerations
[Hand soldering]
4. Soldering
ꢀTemperature profile
Temperature（℃）
（Pb free soldering）
400
300
200
350℃ max
3 sec max
Gradually
cooling
⊿Ｔ
4
100
0
60 sec min
（※⊿Ｔ≦190℃（3216Type max）, ⊿Ｔ≦130℃（3225
Type min）
）
直
※It is recommended to use 20W soldering iron and
the tip is 1φor less.
※The soldering iron should not directly touch the
components.
※Assured to be soldering iron for 1 time.
Note: The above profiles are the maximum allowable
soldering condition, therefore these profiles are
not always recommended.
Caution
1. Use a 20W soldering iron with a maximum tip diameter of 1.0 mm.
2. The soldering iron should not directly touch the capacitor.
5.Cleaning
Cleaning conditions
1. The use of inappropriate solutions can cause foreign substances such as flux residue
to adhere to the capacitor or deteriorate the capacitor's outer coating, resulting in a
degradation of the capacitor's electrical properties（especially insulation resistance）.
2. Inappropriate cleaning conditions（insufficient or excessive cleaning）may detrimen-
tally affect the performance of the capacitors.
1. When cleaning the PC board after the capacitors are all
mounted, select the appropriate cleaning solution according
to the type of flux used and purpose of the cleaning（e.g.
to remove soldering flux or other materials from the produc-
tion process.）
2. Cleaning conditions should be determined after verifying, （1）Excessive cleaning
through a test run, that the cleaning process does not affect
the capacitor's characteristics.
In the case of ultrasonic cleaning, too much power output can cause excessive vibra-
tion of the PC board which may lead to the cracking of the capacitor or the soldered
portion, or decrease the terminal electrodes' strength. Thus the following conditions
should be carefully checked;
Ultrasonic output
Below 20 W/ℓ
Below 40 kHz
Ultrasonic frequency
Ultrasonic washing period 5 min. or less
6.Post cleaning processes
1. With some type of resins a decomposition gas or chemical
reaction vapor may remain inside the resin during the hard-
ening period or while left under normal storage conditions
resulting in the deterioration of the capacitor's performance.
2. When a resin's hardening temperature is higher than the
capacitor's operating temperature, the stresses generated by
the excess heat may lead to capacitor damage or destruction.
The use of such resins, molding materials etc. is not recom-
mended.
Breakaway PC boards（splitting along perforations）
1. When splitting the PC board after mounting capacitors and
other components, care is required so as not to give any
stresses of deflection or twisting to the board.
7.Handling
2. Board separation should not be done manually, but by us-
ing the appropriate devices.
Mechanical considerations
1. Be careful not to subject the capacitors to excessive me-
chanical shocks.
（1）If ceramic capacitors are dropped onto the floor or a
hard surface, they should not be used.
（2）When handling the mounted boards, be careful that the
mounted components do not come in contact with or
bump against other boards or components.
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
117
△
△
PRECAUTIONS
6/6
Precautions on the use of Multilayer Ceramic Capacitors
Stages
Precautions
Technical considerations
8.Storage conditions
Storage
1. If the parts are stored in a high temperature and humidity environment, problems
such as reduced solderability caused by oxidation of terminal electrodes and dete-
rioration of taping/packaging materials may take place. For this reason, components
should be used within 6 months from the time of delivery. If exceeding the above
period, please check solderability before using the capacitors.
1. To maintain the solderability of terminal electrodes and to
keep the packaging material in good condition, care must
be taken to control temperature and humidity in the storage
area. Humidity should especially be kept as low as possible.
・Recommended conditions
4
Ambient temperature
Humidity
Below 30℃
Below 70% RH
The ambient temperature must be kept below 40℃. Even
under ideal storage conditions capacitor electrode solder-
ability decreases as time passes, so should be used within
6 months from the time of delivery.
・Ceramic chip capacitors should be kept where no chlorine or
sulfur exists in the air.
2. The capacitance value of high dielectric constant capacitors
（type 2 &3）will gradually decrease with the passage of time,
so this should be taken into consideration in the circuit design.
If such a capacitance reduction occurs, a heat treatment of
150℃ for 1hour will return the capacitance to its initial level.
！
当社カタログをご使用の際には「当社製品
に関するお断り」を必ずお読みください。
！
Please read the "Notice for TAIYO YUDEN products" before using this catalog.
119
△
△
相关型号：
TMK063UJ060KP-F
Ceramic Capacitor, Multilayer, Ceramic, 25V, 10% +Tol, 10% -Tol, U2J, -750+/-120ppm/Cel TC, 0.000006uF, Surface Mount, 0201, CHIP
TAIYO YUDEN
TMK063UJ060KP-T
Ceramic Capacitor, Multilayer, Ceramic, 25V, 10% +Tol, 10% -Tol, U2J, -750+/-120ppm/Cel TC, 0.000006uF, Surface Mount, 0201, CHIP
TAIYO YUDEN
TMK063UJ070DT
Ceramic Capacitor, Multilayer, Ceramic, 25V, 7.1429% +Tol, 7.1429% -Tol, UJ, -750ppm/Cel TC, 0.000007uF, 0201,
TAIYO YUDEN
TMK063UJ070FP-F
Ceramic Capacitor, Multilayer, Ceramic, 25V, 1% +Tol, 1% -Tol, UJ, -750+/-120ppm/Cel TC, 0.000007uF, Surface Mount, 0201, CHIP, ROHS COMPLIANT
TAIYO YUDEN
TMK063UJ070FP-T
Ceramic Capacitor, Multilayer, Ceramic, 25V, 1% +Tol, 1% -Tol, U2J, -750+/-120ppm/Cel TC, 0.000007uF, Surface Mount, 0201, CHIP
TAIYO YUDEN
TMK063UJ070KP-F
Ceramic Capacitor, Multilayer, Ceramic, 25V, 10% +Tol, 10% -Tol, U2J, -750+/-120ppm/Cel TC, 0.000007uF, Surface Mount, 0201, CHIP
TAIYO YUDEN
TMK063UJ080CP-T
Ceramic Capacitor, Multilayer, Ceramic, 25V, 3.12% +Tol, 3.12% -Tol, U2J, -750+/-120ppm/Cel TC, 0.000008uF, Surface Mount, 0201, CHIP
TAIYO YUDEN
TMK063UJ080DP-F
Ceramic Capacitor, Multilayer, Ceramic, 25V, 6.25% +Tol, 6.25% -Tol, UJ, -750+/-120ppm/Cel TC, 0.000008uF, Surface Mount, 0201, CHIP, ROHS COMPLIANT
TAIYO YUDEN
TMK063UJ080JP-T
Ceramic Capacitor, Multilayer, Ceramic, 25V, 5% +Tol, 5% -Tol, U2J, -750+/-120ppm/Cel TC, 0.000008uF, Surface Mount, 0201, CHIP
TAIYO YUDEN
TMK063UJ090DT-W
Ceramic Capacitor, Multilayer, Ceramic, 25V, 5.56% +Tol, 5.56% -Tol, UJ, 120ppm/Cel TC, 0.000009uF, Surface Mount, 0201, CHIP, LEAD FREE
TAIYO YUDEN
TMK063UJ090JP-F
Ceramic Capacitor, Multilayer, Ceramic, 25V, 5% +Tol, 5% -Tol, U2J, -750+/-120ppm/Cel TC, 0.000009uF, Surface Mount, 0201, CHIP
TAIYO YUDEN
TMK063UJ090JP-T
Ceramic Capacitor, Multilayer, Ceramic, 25V, 5% +Tol, 5% -Tol, U2J, -750+/-120ppm/Cel TC, 0.000009uF, Surface Mount, 0201, CHIP
TAIYO YUDEN
©2020 ICPDF网 联系我们和版权申明